Save time and trouble when installing SPC's adjustable truck sleeves by using this double sided wrench. This wrench is specifically designed to be used with our 24220 and 24230 sleeves and makes on-the-truck adjustments a snap.

California Residents WARNING

This board set gives technicians the tools needed to complete today's modern alignments quickly & efficiently. Contains our most popular tools, with a handy plastic peg storage board to keep all your alignment tools in one easy reference location. Board includes 1 of each of the following: 8370,37985,45938,45940,40840,40850,40860,40870, 40880,74910,77350,77880,81139,83775,85127,85137,87560 and 99918

California Residents WARNING

Replacement gauge fits our stand-along run out gauge #64250.

California Residents WARNING

This custom tool makes adjusting th OE camber cams on the rear of Audis a snap. Even with tires on and the suspension loaded you will be able to access and tighten the nut. Simply loosen the cam bolt, adjust the camber bolt with the bolt's hex pilot, then hold it in place with the hex while you tighten the nut with SPC's custom 12 point box end wrench. The 87570 tool is angled to allow maximum access and clearance for rear camber adjustment.

California Residents WARNING

Expand the service capability of your ball joint press with this Master Ball Joint Adapter Set. This complete kit includes the adapters and receiving tubes needed to work on GM, Ford and Dodge two and four wheel drive trucks, vans and SUVs. Kit also includes a live center forcing screw for heavy duty applications. REPLACEMENT PARTS AVAILABLE - #4159 - Receiving tube - 2.87 OD x 2.62 ID #4415 - Receiving tube - 2.50 OD x 2.25 ID #4416 - Receiving tube - 2.0 OD x 1.75 ID #4417 - Receiving tube - 2.5 od x 2.25 ID #4418 - Receiving tube - 2.13 OD x 1.80 ID #4419 - Receiving tube - 2.5 OD x 2.25 ID x .75 AL #4420 - Receiving tube - 2.5 OD x 2.25 ID x 2.75 AL #4421 - Receiving tube - 3.0 OD x 2.75 ID #4422 - Receiving tube - 2.75 OD x 2.43 ID #4423 - Receiving tube - 2.50 OD x 2.20 ID #4424 - Remover/Installer - 1.50 OD x .82 ID #4425 - Installing tube - 2.0 OD x 1.82 ID #4426 - Receiving cup - 2.12 OD x 1.75 ID

California Residents WARNING

The sleeves are designed to match the angle of the yoke on the axle housing to insure proper installation. Sleeve set 23580 is to be used with our Dodge & Jeep Offset Ball Joints (part nos. 23510, 23520, 23530, 23540). Use in conjuction with the 72509 Ball Joint Press.

California Residents WARNING

Remove and replace ball joints without "brute force" methods that can cause costly damage. Now you can take on 4WD ball joint service in addition to servicing most cars. A forcing screw-powered press, used with proper adapters, easliy removes and installs all press-fit ball joints (inc. GM plastic pin "U" type joints). Comes in a durable plastic case. Package Includes: #4437 - Press #4438- Forcing Screw, #29503- Receiver Tube(3" OD X 2-3/4" ID), #29504- Receiver Tube(2-1/2" OD X 2-1/4" ID), #29505- Receiver Tube(2" OD X 1-3/4" ID), #38354- 4WD Receiving Cup, #38355- Installing Cup, #204508- 4WD Installing Adapter, #305227- Installing Adapter, #305228- Removing Adapter

California Residents WARNING

This heavy duty, drop forged alloy steel, lever-type ball joint and tie rod end remover provides good leverage action to remove stubborn tie rod ends or break ball joint tapers easily. Use when space prevents use of a direct action separator. The 37990 fits 3/4" openings.

California Residents WARNING

Five tools in one, this handy kit consists of three drop forged forks and two handles. One handle is for use with a hammer and one is designed to fit an air hammer. All forks are threaded to interchange with either handle. Comes with 3 forks of 11/16", 15/16" and 1-1/8" openings.

California Residents WARNING

These sockets are used on Chrylser products with screw in ball joints. They have a 3/4" square drive and are four-point, a perfect fit for our ball joints.

California Residents WARNING

These sockets are used on Chrysler products with screw in ball joints. They have a 3/4" square drive and are four-point, a perfect fit for our ball joints.

California Residents WARNING

Quickly and easily adjust rear toe on BMW 3-Series (E46) and Z4 models with this tool from SPC. Simply use your 1/2" drive socket wrench to drive change on the rear toe adjustment brackets on these BMW vehicles and save time on every alignment. Equivalent to BMW tool# 323030 and 83300493306.

California Residents WARNING