Quickly and easily adjust rear camber with this cam and bracket kit designed for the Ford Expedition. Simply replace the OE lock plate and dial camber in exactly where you need it. This kit features a 700 hr salt spray tested coating for corrosion resistance and long service life. Kit is sold per side, you will need two if you are adjusting both sides. Need to add more camber adjustment? Consider our adjustable rear camber arm, SPC PN 67275.

California Residents WARNING

This heavy duty cam-bolt kit was specifically designed for the extreme Raptor & F-150 user. Whether you are a energetic Raptor driver or abuse your F-150 in the fields and on the job site, you may have found that the OE bolts slip or that a single cam option does not hold alignment. This upgraded cam kit features two cams and bosses per bolt. The two cams will keep your bolt square and make adjustments easier while the new bolt and low friction finish achieve 25% more clamp load than the OE hardware. Some drilling is required to accomodate the second boss plate. This kit is sold per wheel and fits Raptors, non-Raptor F-150's and related SUVs. SPC uses a hex chromate free finish and offers a 700hr salt spray test for the best corrosion protection available.

California Residents WARNING

This wedge-type shim fits the 2 hole design of this platform between the rear spring and the axle to change pinion angle. Perfect to align the driveline on vehicles that have been lowered or lifted.

California Residents WARNING

Drive up to ±2° camber and caster change on the front of the Ranger, Explorer, Mountaineeer, and B-Series Pickup by replacing the stock bolt and locking plate with this cam bolt kit from SPC. The 3/8" drive receiver on the cam allows for easy access from either side of the upper control arm to make your changes. This kit includes 4 bolts, enough to do both sides. Need more positive camber for your 2003 - 2011 Ranger 4WD? Check out the 26014 +1° camber shim to get change beyond what the 87500 gives you.

California Residents WARNING

This set of 4 cams allows for quick installation without having to remove the upper control arm bolt. Change camber and caster up to ±1.75°.

California Residents WARNING

Improve droop travel, drivability and tire wear as well as adjusting tire position in your wheel well with SPC's adjustable front upper control arms. Featuring an upgraded greasable ball joint and rubber isolated xAxis bushings, this arm is designed to correct alignment angles while maintaining factory ride quality. SPC's fully forged steel design provides the strength and durability needed for the most demanding environments. These remove and replace arms are sold in pairs.

Get more droop travel: SPC's arm has improved clearance to get around the spring bucket. With 80° of articulation in the upgraded ball joint and free pivoting cross axis bushings, SPC's arm gives you maximum droop travel.

Get your drivability and tracking back: When you lift your truck you affect caster and camber. SPC's patented ball joint design will get you ±2° of caster and ±2° of camber, beyond what the truck's lower slots provide, so you can put your alignment angles back to specification.

Improve tire clearance: Use adjustment in the SPC arm and on the OE lower arm to maximize alignment angles and move oversized tires forward in the wheel well to minimize or avoid fender trimming.

Also consider SPC #86252 with upgraded bolts and adjustment plates to lock in your alignment and prevent bolt slip on the lower control arm.

* On the adjustable ball joint SPC uses hex chromate free finish and offers a 700hr salt spray test for the best corrosion protection available.

California Residents WARNING

Use this kit to change caster and/or camber on these vehicles. Simply replace the existing upper control arm mounting bolts with these cam bolts for caster/camber changes up to ± 2.0°.

California Residents WARNING

Improve droop travel, drivability and tire wear with SPC's adjustable front upper control arms. Fit bigger tires without rubbing fenders. Featuring a greasable ball joint and rubber isolated xAxis bushings, this arm is designed to correct alignment angles on standard height vehicles as well as lifted and lowered vehicles while maintaining factory ride quality. SPC's tube and plate arms are made in our facility in Colorado. Their proven design provides the strength and durability needed for the most demanding environments. These remove and replace arms are sold in pairs.

- Get more droop travel: Don't let the OE ball joints or mono-ball articulation limit your travel. SPC joints are oversized and provide 80° of travel.

- Get your drivability and tracking back: Your truck may have started to 'wander' after you lifted it. That is because you lost caster. Install SPC arms and get your 'drivability' back by putting your alignment in specification.

- Improve tire clearance: Are your oversized tires rubbing the fenders or frame rails? SPC Adjustable Arms, in combination with the OE adjustments on the lower arm, allow you to dial in alignment spcs at the same time that you move the tire forward/outward in the wheel well by up to 1".

NOTE: For Rangers with aluminum knuckles ONLY

California Residents WARNING

Improve droop travel, drivability and tire wear with SPC's adjustable front upper arms for Rangers equipped with steel knuckles. Fit bigger tires without rubbing fenders. Featuring a greasable ball joint and rubber isolated xAxis bushings, this arm is designed to correct alignment angles on standard height vehicles as well as lifted and lowered vehicles while maintaining factory ride quality. SPC's tube and plate arms are made in our facility in Colorado. Their proven design provides the strength and durability needed for the most demanding environments. These remove and replace arms are sold in pairs.

Get more droop travel: Don't let OE ball joint or mono-ball articulation limit your travel. SPC joints are oversized and provide 80° of travel.
Get your drivability and tracking back: Your truck may have started to 'wander' after you lifted it. That is because you lost caster. Install SPC arms and get your 'drivability' back by putting your alignment back in specification.
Improve tire clearance: Are you oversized tires rubbing the fenders or the frame rails? SPC Adjustable Arms, in combination with the OE adjustments on the lower arm, allow you to dial in alignment specs at the same time that you move the tire forward/outward in the wheel well by up to 1".

NOTE: For Rangers with steel knuckles ONLY.

Correct front caster and camber on medium duty Ford trucks with this complete truck sleeve assortment set. This set includes 9 sleeves ranging from 0 to 2° of offset. Have the sleeve you need on the shelf and ready to be used when you need it. Individual sleeves are also available. See part numbers 23221 through 23229.

California Residents WARNING

These truck sleeves will correct caster and camber on trucks equipped with the Dana Super 60 solid axle, like the F450, F550 and GM Toptick. This set includes one each of 9 different sleeves ranging from 0 to 2° offset. Have the sleeve you need on hte shelf and ready to be used when you need it. Individual sleeves are also available. See part numbers 23231 through 23239.

California Residents WARNING

Improve droop travel, drivability and tire wear as well as adjusting tire position in your wheel well with SPC's adjustable front upper control arms for the Ford Ranger (T6 Platform). Featuring our long life maintainable ball joint and SpecRide bushings, this arm is designed to correct alignment angles while maintaining factory ride quality. SPC's integrated tubular and cast steel design provides the strength and durability needed for teh most demanding environments. These remove and replace arms are available in pairs for lifted and off-road applications.

Get more droop travel: SPC's arm has improved clearance to get around the spring bucket when the arm droops, eliminating arm to frame contact on lifted trucks. The maintainable ball joint has an oversized ball and allows more than 80° of articulation to ensure it never binds. SpecRide bushings have free pivot to eliminate any chance of bushing failure seen on many high travel suspensions.

Get your drivability and tracking back: When you lift your truck you affect caster and camber. SPC's arms have +1° of caster built into them. Using its patented ball joint design the arm will get you -1° to +4° of caster and ±3° of camber.

Get your tire where you want it in the wheel well: Use adjustment in the control arm and on the OE lower cams to maximize alignment angles and move oversized tires forward in the wheel well to minimize or avoid fender trimming.

California Residents WARNING