Make camber changes in +.5° or +1.0° on many popular models by installing this shim between the hub and steering knuckle. A caliper shim is also included. These durable high-strength nylon shims provide a faster option for correcting negative camber issues.

California Residents WARNING

Make camber changes in +.5° or +1.0° on many popular models by installing this shim between the hub and steering knuckle. A caliper shim is also included. These durable high-strength nylon shims provide a faster option for correcting negative camber issues.

California Residents WARNING

This new kit allows for easy adjustment of the lower control arm to make camber and caster changes. Uses the O.E. bolts with the new cams and adjusting plates to give you lifetime camber and caster adjustments.

California Residents WARNING

Caster and camber adjustments can be made easily by installing this kit. By replacing the stock alignment washers on the upper control arm, caster and camber can be adjusted by turning the cam nuts to obtain the proper readings. These cam kits give you the full range of caster and camber adjustment and once installed make alignments quick and easy for the life of the vehicle.

California Residents WARNING

Replace corroded or damaged original equipment alignment cams on GM and Chevy 1500 trucks with this cam and bolt kit. SPC's replacement camber and caster cam kit includes a provision for 3/8" drive ratchet wrench when the bolt head is difficult to reach. Use part number 86326 HD GM alignment pins to replace the often abused or missing OE pins.

California Residents WARNING

Get your GM truck or SUV's front camber or caster back in spec with these fixed offset upper control arms. Whether you lift your rig 3" or lower it 1" it is going to lose caster. The OE adjusters do not provide enough change, so install SPC offset arms for +2° caster change and then use the OE cams to dial your alignment in and get your drivability back. These arms feature:

*Fully forged contruction for maximum strength.

*Booted and greasable ball joints that will last.

*SPC's xAxis technology with a twist. The xAxis sealed flext joints used in these arms provide a free pivot for droop and misalignment that OE caster and camber adjustments will not bind the joint. These cross axis ball joints also have rubber isolation to retain OE bushing values for Noise, Vibration, and Harshness (NVH).

Kit includes arms for both the right and left hand side. It can be used for lifted and lowered applications, if you drop your ride height more than 1" it will start to gain caster very quickly. These arms will still work for you, swap these arms left to right and get -2° caster change if you need it. Need to replace the OE adjusters? Consider SPC's p/n 86375 replacement cams, p/n 86325 replacement alignment pins and p/n 86320 alignment locking plates.

California Residents WARNING

Replace corroded or damaged original equipment alignment cams on GM 2500/3500/4500 HD trucks and Chevy Colorados with this cam and bolt kit. SPC's replacement camber & caster cam kit includes a provision for 3/8" drive ratchet wrench when the bolt head is difficult to reach. Use part number 86326 HD GM alignment pins to replace the often abused or missing OE pins.

California Residents WARNING

This lock plate is designed to keep the front alignment angles in position by replacing the existing slotted cam. For newer models of GMC's 1500, 2500 and 3500 vehicles.

California Residents WARNING

GM's late-model mid-sized 4WD's have very little clearance to adjust the camber and caster with the OE adjusting cams. These specially designed adjusters replace the OE adjusters, and feature a 3/8" square drive hole, allowing fast and easy "on the vehicle" adjustments with any standard breaker bar. The unique design saves time by installing onto the OE bolt - and allows for quick future adjustments.

California Residents WARNING

These heavy duty offset ball joints have a built in 3 degree offset which can be clocked to affect camber, caster, or both. They are ideal for vehicles which cannot be aligned properly with the factory cam bolts due to installation of a lift or leveling kit. As an additional benefit, they also raise the outer end of the upper control arm, which increases clearance between the arm and the droop travel stops on the frame. This restores droop travel on trucks with leveling kits, and eliminates noise vibration harshness caused by arm to frame contact. Note: Due to strength limitations of the factory upper control arm, this ball joint should not be used on trucks with tires larger than 33" unless a "tall knuckle" lift kit is installed. SPC uses hex chromate free finish and offers a 700hr salt spray test for the best corrosion protection available.

California Residents WARNING

Replace your stripped or corroded factory adjusters on GM's Lambda platform vehicles with SPC's rear camber and toe adjustment bolts. This pair of camber bolts can be used to replace camber or toe bolts on either side of the car. You will need 2 kits to replace all four positions. This kit provides the same adjustment range as the factory cam bolts. Need front camber adjustment? The Lambda platform can use SPC's EZ cams to add quick camber correction on the front suspension. SPC uses a hex chromate free finish and offers a 700hr salt spray test for the best corrosion protection available.

California Residents WARNING

Replace failed cross axis ball joints and frozen cam adjusters on the rear upper control arm of GM's popular lambda platform vehicles with SPC's cam bolt and xAxis kit. This will let you adjust camber ±2°. Kit replaces cross axis ball joint and hardware on the inboard end of both the RH and LH arms. Part numbers: 23347603 and 23347602.

California Residents WARNING