This pair of rear lower control arms are direct replacements for weak or bent factory units. Made of 3/16" wall DOM tube, they are more than 2x stronger than the OEM arms! They are equipped with a rubber bushing in one end for isolation of axle noise and xAxis joints in the opposite end for superior flexibility off road. Whether you are replacing damaged OE parts or upgrading for offroad use, these are the arms for you. Need articulation or alignment changes in the front? Check out the 25455 front adjustable upper control arms!

California Residents WARNING

This pair of rear lower control arms are direct replacements for weak or bent factory units on the 200 Series Landcruiser. Made of 3/16" wall DOM tube, they are more than 2x stronger than the OEM arms! They are equipped with a rubber bushing in one end for isolation of axle noise, with an xAxis sealed flex joint in the other end for superior flexibility off road. Whether you are replacing damaged OE parts or upgrading for off road use, these are the arms for you. Need caster/camber adjustment or increased articulation on the front? Use our 25465 fully adjustable upper control arms allowing for full travel for your off road needs.

California Residents WARNING

This pair of lower control arms are direct replacements for weak or bent factory units. Made of 3/16" wall DOM tube, they are more than 2x stronger than the OEM arms! They are equipped with a rubber bushing in one end for isolation of road noise and xAxis sealed flex joints in the other end for superior flexibility off road. Whether you are replacing damaged OE parts or upgrading for offroad use, these are the arms for you. Have you lifted your 3rd Gen 4Runner and want to get your drivability back? Check out SPC's 25460 adjustable front upper control arms!

California Residents WARNING

Replace worn out bushings on your 1996 through 2002 Toyota 4Runner rear upper trailing link with this replacement bushing from SPC. These bushings are sold each and fit both the inboard and outboard location on this upper arm. Need pinion angle adjustment? Consider replacing the arms instead with SPC# 25390.

California Residents WARNING

Replace worn track bar bushings on your 1996 through 2002 Toyota 4Runner with this replacement bushing from SPC. Sold each, use up to two bushings on your vehicle. Need to adjust your rear track? Consider replacing your track bar instead with SPC# 25395.

California Residents WARNING

This pair of rear lower control arms are direct replacements for weak or bent factory units on the 80 series Landcruiser. Made of 3/16" wall DOM tube, they are more than 2x stronger than the OEM arms! They are equipped with a rubber bushing in one end for isolation of axle noise, with a xAxis sealed flex joint in the other end for superior flexibility off road. Whether you are replacing damaged OE parts or upgrading for off road use, these are the arms for you.

California Residents WARNING

The front upper control arm mounting bolts on the Ford Bronco are frequently corroded and must be cut out when removing or replacing the control arm. This hardware replacement kit allows quick and easy re-installation of the upper control arm. This long bolt and nut kit will service the control arm hardware on one side of the vehicle. Order two kits to replace both sides.

California Residents WARNING

The front upper control arm mounting bolts on many Toyota truck and SUV models are frequently corroded and must be cut out when removing or replacing the control arm. This hardware replacement kit allows quick and easy re-installation of the upper control arm. This long bolt and nut kit will service the control arm hardware on one side of the vehicle. Order two kits to replace both sides.

California Residents WARNING

These offset pin joints replace the upper jin joints on late model Dodge Trucks. They come in 1/2 degree increments and provide for independent wheel caster and/or camber changes up to 1-1/2 degrees. Use installation sleeve set 23780 in conjunction with ball joint press 72509 for quick removal and installation of the pin joints. -------------NOTE: 23800 is an OEM Replacement Ball Joint with no change in camber or caster.

California Residents WARNING

Replace your worn fronter lower control arm bushings on the 2018 and newer Jeep Wrangler (JL) or Gladiator (JT) with this replacement bushing from SPC. Sold each, use two bushings per control arm, up to four per vehicle. Need caster or front pinion angle adjustment? Consider adding SPC# 82375 at the same time.

California Residents WARNING

The upper control arm mounting bolts on many Nissan Trucks and SUV's are frequently corroded and must be cut out when removing or replacing the control arm. This hardware replacement kit (2) allows easy re-installation of the upper control arm. The pair of bolts and nuts are enough to replace both bolts in one corner or to replace the rearward bolt on both upper control arms if you are cutting them out to replace both arms.

California Residents WARNING

This pair of rear lower control arms are direct replacements for weak or bent factory units. Made of 3/16" wall DOM tube, they are more than 2x stronger than the OEM arms! They are equipped with a rubber bushing in one end for isolation of road noise and xAxis sealed flex joints in the other end for superior flexibility off road. Whether you are replacing damaged OE parts or upgrading for offroad use, these are the arms for you. Need articulation or alignment changes in the front? Check out the 25480 front adjustable upper control arms!

California Residents WARNING