High flow version of our 3.0" 25715 Jounceshock.

Double your suspension capacity: 9" long base unit is ideal for 1:1 motion ratios

California Residents WARNING

For camber and toe change, use our Mini-Van Shims that allow for quick and easy changes in increments of: toe .10 degrees and camber .25 degrees. CAUTION:check brake and rotor clearance for binding.75970 spacers may be required. DO NOT use spacers with AWD vehicles.

California Residents WARNING

These popular sleeves are widely used to adjust caster and/ or camber on many Ford and Mazda RWD & 4WD trucks. To install, simply loosen and remove upper ball joint pinch bolt. Remove top snap ring if one is present. Use 77880 or 88830 sleeve puller to remove the existing sleeve. To split camber and caster adjustment, rotate sleeve 45°. Save time during alignment, use 23199 zero degree sleeve to determine initial readings, then install correct sleeve. Note: Sleeves adjust to a smaller degree on Ford and Mazda 4WD light trucks/SUVS.

California Residents WARNING

These popular sleeves are widely used to adjust caster and/ or camber on many Ford and Mazda RWD & 4WD trucks. To install, simply loosen and remove upper ball joint pinch bolt. Remove top snap ring if one is present. Use 77880 or 88830 sleeve puller to remove the existing sleeve. To split camber and caster adjustment, rotate sleeve 45°. Save time during alignment, use 23199 zero degree sleeve to determine initial readings, then install correct sleeve. Note: Sleeves adjust to a smaller degree on Ford and Mazda 4WD light trucks/SUVS.

California Residents WARNING

These 3-3/4" steel adjusting sleeves are the perfect fit with our pivot studs and ball joint plates.

California Residents WARNING

Change camber,caster or both at the same time with these sleeves. Simply remove the tire, cotter pin and upper ball joint stud nut and break the taper free between the stud and sleeve. Using a sleeve puller, remove the existing sleeve. Install a zero degree sleeve 23139 to determine the change needed ,then install the correct sleeve.To split camber and caster adjustment, rotate sleeve 45°.

California Residents WARNING

These popular sleeves are widely used to adjust caster and/ or camber on many Ford and Mazda RWD & 4WD trucks. To install, simply loosen and remove upper ball joint pinch bolt. Remove top snap ring if one is present. Use 77880 or 88830 sleeve puller to remove the existing sleeve. To split camber and caster adjustment, rotate sleeve 45°. Save time during alignment, use 23199 zero degree sleeve to determine initial readings, then install correct sleeve. Note: Sleeves adjust to a smaller degree on Ford and Mazda 4WD light trucks/SUVS.

California Residents WARNING

Fix front camber issues on your Jeep Wrangler (JL) by replacing the camber sleeve that links the upper ball joint to knuckle. Simply determine what degree offset sleeve is already in the knuckle and replace it with a new offset. Jeeps coming off the line right now have +1/4° sleeves on both sides, if you need to add 1/2° of camber you will want to install this 3/4° camber sleeve. SPC's camber sleeves feature our hex chromate free finish certified to a 700 hour salt spray test. Do you align a lot of Jeeps or are you not sure how much change you will need? Consider SPC's 6 piece set which includes one of each sleeve ranging from 0° to +1.25°. P/N 23400

California Residents WARNING

This sleeve changes camber and caster on many older model trucks and SUVs with Dana 44 or GMC 10 bolt axles. 4169 spanner socket is required for sleeve removal. Rotate sleeve to fine tune camber/caster adjustment.

California Residents WARNING

Change camber,caster, or both on twin traction beam Dana 44s with these sleeves. Simply remove the tire, cotter pin and upper ball joint stud nut and break the taper free between the stud and sleeve. Using a sleeve puller, remove the existing sleeve. Unstall zero degree sleeve 23109 to determine the change needed, then install the correct sleeve. To split camber and caster adjustment, rotate sleeve 45°.

California Residents WARNING

These truck sleeve will correct alignment problems on the F450 and F550 Super Duty trucks with Dana Super 60 solid axles. To split camber and caster adjustment, rotate sleeve 45° Use the 23239 zero degree sleeve to determine the amount of change needed.

California Residents WARNING