For steer and drive axles. This wheel centering sleeve slide s over the studs and seats against the wheel face. This slee ve stays on the wheel and helps to reduce "wheel-off" condit ion. Sold in sets of 6 per axle. Zinc plated to resist corro sion.

California Residents WARNING

Adjustable upper control arm includes 6" aluminum cross shaft, 8-1/4" to 10" adjustment sleeves and fullsize GM plate.

California Residents WARNING

Adjustable upper control arm includes 6" aluminum shaft, 8-1/4" to 10" sleeves and threaded 10° plate.

California Residents WARNING

Sometimes the front stabilizer may rub against the spring well housing. If this situation occurs, the stabilizer must be installed from the inside of the coil springs. Two sizes of short-nosed stabilizers are available: 24701 (a "short-nosed" 24700); 24751 (a "short nosed" 24750). Two stabilizer's are recommended per coil spring. (no more, no less). 4 per pack. Height ("A") = 5/8"

California Residents WARNING

Sometimes the front stabilizer may rub against the spring well housing. If this situation occurs, the stabilizer must be installed from the inside of the coil springs. Two sizes of short-nosed stabilizers are available: 24701 (a "short-nosed" 24700); 24751 (a "short nosed" 24750). Two stabilizer's are recommended per coil spring. (no more, no less). 4 per pack. Height ("A") = 5/8"

California Residents WARNING

Adjustable Upper Control Arm with 6" aluminum cross shaft, 3-3/4" adjusting sleeves and a Full Size GM ball joint plate. Sleeves adjust from 7" to 9".

California Residents WARNING

Adjustable Upper Control Arm with 6" aluminum cross shaft, 3-3/4" adjusting sleeves and a 10° Chrylser screw in ball joint plate. Sleeves adjust from 7" to 9".

California Residents WARNING

Build your next project with these forged steel alloy threaded receivers and xAxis sealed flex joints from SPC Performance. Get the increased angularity of a mono-ball that has been equipped with high mis-alignment inserts, the reduced compliance of a spherical bearing, and better durability than rubber and urethane bushings with SPC's superior design. This assembly has RH M18-1.5 threads takes a 12mm bolt and is 40mm wide. 19° of articulation, sealed dust boots, moly grease and a highly polished electroless nickel ball makes this the best joint on the market. These assemblies utilize a snap ring for positive retention and easy replacements. Download a package model into your CAD software and start designing today.

California Residents WARNING

Build your next project with these forged steel alloy threaded receivers and xAxis sealed flex joints from SPC Performance. Get the increased angularity of a mono-ball that has been equipped with high mis-alignment inserts, the reduced compliance of a spherical bearing, and better durability than rubber and urethane bushings with SPC's superior design. This assembly has LH M18-1.5 threads takes a 12mm bolt and is 40mm wide. 19° of articulation, sealed dust boots, moly grease and a highly polished electroless nickel ball makes this the best joint on the market. These assemblies utilize a snap ring for positive retention and easy replacements. Download a package model into your CAD software and start designing today.

California Residents WARNING

Get 45° of articulation when you build with these forged steel alloy threaded receivers and xAxis sealed flex joints. This assembly has RH 1 1/4"-12 threads takes a 9/16" bolt and is 2.625" wide. It comes with a jam nut for your convenience and is a perfect upgrade for Jeep TJ and JK lower control arm bushings. The kit comes with everything you need to replace / upgrade your worn joints. This assembly utilizes a snap ring for positive retention and allows for easy replacement.

California Residents WARNING

Get 45° of articulation when you build with these forged steel alloy threaded receivers and xAxis sealed flex joints. This assembly has LH 1 1/4"-12 threads takes a 9/16" bolt and is 2.625" wide. It comes with a jam nut for your convenience and is a perfect upgrade for Jeep TJ and JK lower control arm bushings. The kit comes with everything you need to replace / upgrade your worn joints. This assembly utilizes a snap ring for positive retention and allows for easy replacement.

California Residents WARNING

Build your next project with these forged steel alloy threaded receivers and xAxis sealed flex joints from SPC Performance. Get the increased angularity of a mono-ball that has been equipped with high mis-alignment inserts, the reduced compliance of a spherical bearing, and better durability than rubber and urethane bushings with SPC's superior design. This assembly has RH 1/2"-20 threads takes a 3/8" bolt and is 1.5" wide. 45° of articulation, sealed dust boots, moly grease and a highly polished electroless nickel ball makes this the best joint on the market. These assemblies utilize a snap ring for positive retention and easy replacements. Download a package model into your CAD software and start designing today.

California Residents WARNING