Direct positive or negative toe change in .50° increment is made quickly and accurately with this shim. Combine this toe shim with a camber shim (71051-71056) to get the exact toe and camber change that is required. Stack up to two shims.

California Residents WARNING

Direct positive or negative toe change in .40° increment is made quickly and accurately with this shim. Combine this toe shim with a camber shim (71051-71056) to get the exact toe and camber change that is required. Stack up to two shims.

California Residents WARNING

A patented Full Contact Dual Angle Shim, that corrects Toe and Camber with one shim. These two-piece adjustable shims are available in 4 sizes which cover many rear shimable FWD vehicles. Durable construction, proven adjustment changes within .03 degrees toe and .01 degrees camber. CAUTION: Check for caliper to rotor clearance when installing this part on vehicles equipped with rear disc brakes. Some vehicles may require the use of longer bolts. Recommend use of 10408 bolts and 75970 spacers as required. Recommend use of 75915 Shim Cutter. 75910 Dial Chart and EZ SHim Online available for setting shims.

California Residents WARNING

Make rear wheel alignment changes on these twist beam axles with SPC's stackable fixed change shims. Change camber in ±.25° increments and toe in ±.10° increments. Combine a toe shim with a camber shim to get the exact change required. Stack up to two shims for maximum change.

California Residents WARNING

Make rear wheel alignment changes on these twist beam axles with SPC's stackable fixed change shims. Change camber in ±.25° increments and toe in ±.10° increments. Combine a toe shim with a camber shim to get the exact change required. Stack up to two shims for maximum change.

California Residents WARNING

Add a little horsepower, use grippy tires, launch hard, and take a corner at 1.5 G's. You need an adjustable rear control arm to optimize your tire contact by adjusting your camber. Be confident your arm is proven and reliable for the >1,000 pounds of force that it will be loaded with over and over again as you put your Mustang to the test. Designed, engineered, tested, and assembled in Colorado, SPC's forged aluminum link will provide; -3 to +2 degrees of camber adjustment, reduced weight vs the OE arm and exceed its strength. SPC's adjustable arm features high rate rubber bushings to maintain OE noise, vibration, and harshness (NVH) and has a 1.5" hexed eccentric insert at the knuckle end of the arm to easily adjust camber without removing the tire. All hardware is included and features hex chromate free finish (certified to 700 salt spray test standards) for a long rust free life.

California Residents WARNING

Make rear wheel alignment changes on these twist beam axles with SPC's stackable fixed change shims. Change camber in ±.25° increments and toe in ±.10° increments. Combine a toe shim with a camber shim to get the exact change required. Stack up to two shims for maximum change.

California Residents WARNING

Make rear wheel alignment changes on these twist beam axles with SPC's stackable fixed change shims. Change camber in ±.25° increments and toe in ±.10° increments. Combine a toe shim with a camber shim to get the exact change required. Stack up to two shims for maximum change.

California Residents WARNING

Adjust rear camber on late model RAV4 and Lexus NX200t with this adjustable rear camber arm. With ±3.0° of adjustment, this arm will get your vehicle back into factory specification to ensure proper tire wear, handling, and ride quality. Use part number 67810 for the right hand side or part number 67811 for the left hand side of the rear suspension.

California Residents WARNING

Adjust rear camber on late model RAV4 and Lexus NX200t with this adjustable rear camber arm. With ±3.0° of adjustment, this arm will get your vehicle back into factory specification to ensure proper tire wear, handling, and ride quality. Use part number 67811 for the left hand side or part number 67810 for the right hand side of the rear suspension.

California Residents WARNING

Fix your rear toe on Hyundai Accent and Kia Rio models with this shim set from SPC. Fix tire wear, thrust angle, and poor drivability by getting the rear toe back into specification. This kit includes 2 each of the 0.13°, 0.25°, 0.38°, and 0.50° shims for maximum coverage and can be used for either positive or negative change.

California Residents WARNING

Direct positive camber change in .50° increment is made quickly and accurately with this shim. Combine this camber shim with a toe shim (71051-71055)to get the exact camber and toe change that is required. Stack up to two shims.

California Residents WARNING