3/8° Nylon Rear Shim.

California Residents WARNING

3/8° Nylon Rear Shim.

California Residents WARNING

With these shims you can correct both rear camber and toe on newer Volkswagens & Audis. By combining the shims (two may be used per wheel) you can get up to +/-.50 degrees toe Our wrench (87530) is a must when installing these shims. It allows you to remove the brake tone ring, bearing, seal and hub assembly as one unit. CAUTION: Check brake & rotor clearance for binding. 75970 spacers may be required.

California Residents WARNING

This easy to install full contact shim is perfect for European Models needing rear toe adjustment. SPC's fixed change shims will provide ±.13° to ±.50° of toe change.

California Residents WARNING

These popular sleeves are widely used to adjust caster and/ or camber on many Ford and Mazda RWD & 4WD trucks. To install, simply loosen and remove upper ball joint pinch bolt. Remove top snap ring if one is present. Use 77880 or 88830 sleeve puller to remove the existing sleeve. To split camber and caster adjustment, rotate sleeve 45°. Save time during alignment, use 23199 zero degree sleeve to determine initial readings, then install correct sleeve. Note: Sleeves adjust to a smaller degree on Ford and Mazda 4WD light trucks/SUVS.

California Residents WARNING

Spread the load! "Z" blocks and other axle spacers used by Hendrickson, Freightliner, Kenworth, Mack, Hollis, Sterling, Ford and others create pressure points that will crush or even break the toughest of caster wedges. Use this HD Wedge Spacer Plate to spread the load and then use the caster shim of your choice to modify alignment. The 1/8" thick plate comes 6 to a pack and provides support for 3" wide axle spacers. The HD Wedge Spacer Plate can also be used to dial in ride height from side to side.

California Residents WARNING

For camber and toe change, use our Mini-Van Shims that allow for quick and easy changes in increments of: toe .10 degrees and camber .25 degrees. CAUTION:check brake and rotor clearance for binding.75970 spacers may be required. DO NOT use spacers with AWD vehicles.

California Residents WARNING

These 4" anodized aluminum adjusting sleeves are the perfect fit with our pivot studs and ball joint plates.

California Residents WARNING

Spread the load! "Z" blocks and other axle spacers used by Hendrickson, Freightliner, Kenworth, Mack, Hollis, Sterling, Ford and others create pressure points that will crush or even break the toughest of caster wedges. Use this HD Wedge Spacer Plate to spread the load and then use the caster shim of your choice to modify alignment. The 1/8" thick plate comes 6 to a pack and provides support for 4" wide axle spacers. The HD Wedge Spacer Plate can also be used to dial in ride height from side to side.

California Residents WARNING

Improve droop travel, drivability and tire wear as well as adjusting tire position in your wheel well with SPC's adjustable front upper control arms on many Toyota trucks and SUVs. Featuring our long life maintainable ball joint and SpecRide bushings, this arm is designed to correct alignment angles while maintaining factory ride quality. SPC's integrated tubular and cast steel design provides the strength and durability needed for the most demanding environments. These remove and replace arms are available in pairs for lifted and off-road applications.

Get more drrop travel: SPC's arm has improved clearance to get around the spring bucket when the arm droops, eliminating arm to frame contact on lifted trucks. The maintainable ball joint has an oversized ball and allows for more than 80° of articulation to ensure it never binds. SpecRide bushings have free pivot to eliminate any chance of bushing failure seen on many high travel suspensions.

Get your drivability and tracking back: When you lift your truck you affect caster and camber. SPC's arms have +1° of caster built into them. Using its patented ball joint design the arm will get you 0° to +4° of caster and ±2° of camber.

Get your tire where you want it in the wheel well: Use adjustment in the control arm and on the OE lower cams to maximize alignment angles adn move oversized tires forward in the wheel well to minimize or avoid fender trimming.

* On the adjustable ball joint SPC uses hex chromate free finish and offers a 700hr salt spray test for the best corrosion protection available.

California Residents WARNING

This pair of lower control arms are direct replacements for weak or bent factory units. Made of 3/16" wall DOM tube, they are more than 2x stronger than the OEM arms! They are equipped with a rubber bushing in one end for isolation of road noise and xAxis sealed flex joints in the other end for superior flexibility off road. Whether you are replacing damaged OE parts or upgrading for offroad use, these are the arms for you. Have you lifted your 3rd Gen 4Runner and want to get your drivability back? Check out SPC's 25460 adjustable front upper control arms!

California Residents WARNING

Replace worn out bushings on your 1996 through 2002 Toyota 4Runner rear upper trailing link with this replacement bushing from SPC. These bushings are sold each and fit both the inboard and outboard location on this upper arm. Need pinion angle adjustment? Consider replacing the arms instead with SPC# 25390.

California Residents WARNING