Improve droop travel, drivability and tire wear with SPC's adjustable front upper arms for Rangers equipped with steel knuckles. Fit bigger tires without rubbing fenders. Featuring a greasable ball joint and rubber isolated xAxis bushings, this arm is designed to correct alignment angles on standard height vehicles as well as lifted and lowered vehicles while maintaining factory ride quality. SPC's tube and plate arms are made in our facility in Colorado. Their proven design provides the strength and durability needed for the most demanding environments. These remove and replace arms are sold in pairs.

Get more droop travel: Don't let OE ball joint or mono-ball articulation limit your travel. SPC joints are oversized and provide 80° of travel.
Get your drivability and tracking back: Your truck may have started to 'wander' after you lifted it. That is because you lost caster. Install SPC arms and get your 'drivability' back by putting your alignment back in specification.
Improve tire clearance: Are you oversized tires rubbing the fenders or the frame rails? SPC Adjustable Arms, in combination with the OE adjustments on the lower arm, allow you to dial in alignment specs at the same time that you move the tire forward/outward in the wheel well by up to 1".

NOTE: For Rangers with steel knuckles ONLY.

This sleeve set will change camber and/or caster from 1/8 degree to 1-1/2 degree in 1/4 degree increments. Installation requires removal of the upper ball joint stud nut. Break the taper free between the stud and sleeve. Determine the change needed and replace the existing sleeve with the correct one. #4169 spanner socket required for sleeve removal. Set includes 6 sleeves.

California Residents WARNING

Replace your worn fronter lower control arm bushings on the 2018 and newer Jeep Wrangler (JL) or Gladiator (JT) with this replacement bushing from SPC. Sold each, use two bushings per control arm, up to four per vehicle. Need caster or front pinion angle adjustment? Consider adding SPC# 82375 at the same time.

California Residents WARNING

Make rear camber on the Mazda CX-5 adjustable for life with this adjustable lower control arm and extended range toe cam kit. The remove and replace camber arm provides ±3.0° of change and the included extended range toe cam will get toe back to specification through the entire camber range. Whether you need to adjust to improve handling or decrease tire wear issues, this is the kit for you. Use rotary file #85130 to extend the factory toe slot and take advantage of the full throw provided by the SPC's extended toe cam bolt. Also includes an optional bracket for use with '17 & newer models that include an air dam on the lower control arm.

California Residents WARNING

This fully adjustable rear lower control arm restores lost adjustment on many Ford Explorer vehicles. Ford has recalled many of these vehicles for corrosion issues and this recall removes any toe adjustability in the suspension. This SPC control arm restores the full adjustment range and allows proper alignemtn settings to avoid premature tire wear. Sold per control arm, order two to service both sides of the vehicle. Need rear camber adjustment as well? Consider SPC PN# 84130.

California Residents WARNING

Replacement bushing kit for 25540 and 25485 upper arms.

California Residents WARNING

Replace worn out bushings on your 1996 through 2002 Toyota 4Runner rear upper trailing link with this replacement bushing from SPC. These bushings are sold each and fit both the inboard and outboard location on this upper arm. Need pinion angle adjustment? Consider replacing the arms instead with SPC# 25390.

California Residents WARNING

Replace worn track bar bushings on your 1996 through 2002 Toyota 4Runner with this replacement bushing from SPC. Sold each, use up to two bushings on your vehicle. Need to adjust your rear track? Consider replacing your track bar instead with SPC# 25395.

California Residents WARNING

Replace damaged or corroded factory adjusters for your Nissan Rogue with this replacement cam bolt from SPC. This kit features a hex chromate free fnish that offers a 700hr salt spray test for the best corrosion protection available. One kit is used for each side of the vehicle and can be used in either the camber or toe adjustment position for a maximum of 4 bolt kits needed per vehicle.

This pair of lower control arms are direct replacements for weak or bent factory units. Made of 3/16" wall DOM tube, they are more than 2x stronger than the OEM arms! They are equipped with a rubber bushing in one end for isolation of road noise and xAxis sealed flex joints in the other end for superior flexibility off road. Whether you are replacing damaged OE parts or upgrading for offroad use, these are the arms for you. Have you lifted your 3rd Gen 4Runner and want to get your drivability back? Check out SPC's 25460 adjustable front upper control arms!

California Residents WARNING

Add more adjustment to the rear suspension on your Ford Expedition with this fully adjustable camber control arm. This arm replaces the factory non-adjustable upper control arm and allows easy on-car adjustment to dial in the camber exactly where you want it. The bonded rubber bushing retains factory ride and vibration quality while providing a long service life.